U-Boot 1.1.1 (Sep 13 2005 - 12:41:26) GRASP U-Boot 1.2 (Sep 13 2005 - 12:41:26) r6464 MPC8272 Reset Status: External Soft, External Hard MPC8272 Clock Configuration - Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300 - dfbrg 1, corecnf 0x1a, busdf 4, cpmdf 1, plldf 0, pllmf 4 - vco_out 330000000, scc_clk 82500000, brg_clk 20625000 - cpu_clk 264000000, cpm_clk 165000000, bus_clk 66000000 - pci_clk 55000000 CPU: MPC8272 (HiP7 Rev 14, Mask A.0 1K50M) at 264 MHz checkboard() DRAM: 64 MB Top of RAM usable for U-Boot at: 04000000 Reserving 2283k for U-Boot at: 03dc5000 Reserving 4159k for malloc() at: 039b5004 Reserving 188 Bytes for Board Info at: 039b4f48 Reserving 76 Bytes for Global Data at: 039b4efc Stack Pointer at: 039b4ed8 New Stack Pointer is: 039b4ed8 FLASH: Flash is 256 sectors of 131072 bytes each 32 MB Using default environment readonly: ethaddr=00:14:4F:0E:24:0D In: serial Out: serial Err: serial misc_init_r() Reset Ethernet PHY reset_phy() U-Boot relocated to 0x03dc5000 Net: FCC1 ETHERNET Booting linux in 2 seconds... Boot Path ID = 0x1 Programming BOB from Flash Memory ## Scanning Flash memory for Bob microcode... Found. ## Unzipping microcode at fff60040 ... done. Programming now... Programming complete Done bit is 1 Program Bob success Found INITRD Image for Root File System @ /dev/mtdblock1 flash address ff5a0000 root @ /dev/mtdblock1 Address ff5a0000 www @ /dev/mtdblock2 Address ffc60000 params @ /dev/mtdblock3 Address ffdc0000 Booting from MODULE_PIMAGE ... Bootargs = [ro root=/dev/ramdisk ip=none ramdisk_blocksize=4096 console=ttyS0,9600] ## Booting image at 00c00000 ... Image Name: Linux-2.4.22 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 706865 Bytes = 690.3 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Current stack ends at 0x039B4A60 => set upper limit to 0x00A00000 ## cmdline at 0x009FFF00 ... 0x009FFF46 memstart = 0x00000000 memsize = 0x04000000 flashstart = 0xFE000000 flashsize = 0x02000000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 EnvAddr = 0xFFF40000 EnvSize = 0x0000FFFC immr_base = 0xF0000000 bootflags = 0x00000001 vco = 330 MHz sccfreq = 82.500 MHz brgfreq = 20.625 MHz intfreq = 264 MHz cpmfreq = 165 MHz busfreq = 66 MHz ethaddr = 00:14:4F:0E:24:0D IP addr = 192.168.2.4 baudrate = 9600 bps ## Loading RAMDisk Image at ff5a0000 ... Image Name: Image Type: PowerPC Linux RAMDisk Image (uncompressed) Data Size: 6864896 Bytes = 6.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## initrd at 0xFF5A0040 ... 0xFFC2C03F (len=6864896=0x68C000) Loading Ramdisk to 00373000, end 009ff000 ... OK ## Transferring control to Linux (at address 00000000) ... ## parameters(009ffe40,00373000,009ff000,009fff00,009fff46) Memory BAT mapping: BAT2=32Mb, BAT3=16Mb, residual: 46Mb Mapping Peripheral 2 @ Base 0xE0000000 for Size 0x01000000 Mapping Peripheral 3 @ Base 0xD0000000 for Size 0x00008000 Mapping Peripheral 4 @ Base 0xD0008000 for Size 0x00008000 Mapping Video Memory @ Phys 0x03e00000 to Virt @ 0xe1000000 of Size 0x00200000 Linux version 2.4.22 (bill@luai.sfbay.sun.com) (gcc version 3.3.4) #1 Tue Sep 13 12:42:45 PDT 2005 r6464 On node 0 totalpages: 15872 zone(0): 15872 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: ro root=/dev/ramdisk ip=none ramdisk_blocksize=4096 console=ttyS0,9600 Calibrating delay loop... 175.71 BogoMIPS Memory: 54344k available (1192k kernel code, 412k data, 68k init, 0k highmem) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. CPM UART driver version 0.01 ttyS0 at 0x8000 is a SCC ttyS1 at 0x8300 is a SCC pty: 256 Unix98 ptys configured Generic RTC Driver v1.07 eth0: FCC ENET Version 0.2, 00:14:4f:0e:24:0d fec: Phy @ addr=4, type 0x004061e4 PHY control: 0x00003000 PHY status : 0x00007829 autoneg adv: 0x000001e1 Int 1a: 0x00009f00 AuxMode2 1b: 0x0000008a fec: link up,auto complete RAMDISK driver initialized: 16 RAM disks of 18432K size 4096 blocksize loop: loaded (max 8 devices) Ractrends Flash mapping: 0x2000000 at fe000000 Amd/Fujitsu Extended Query Table v1.3 at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. MTD Partition 0 : fullpart @ 0x0 of Size 0x2000000 MTD Partition 1 : root @ 0x15a0000 of Size 0x6a0000 MTD Partition 2 : www @ 0x1c60000 of Size 0x140000 MTD Partition 3 : params @ 0x1dc0000 of Size 0x120000 MTD Partition 4 : coredump @ 0x20000 of Size 0xfe0000 Creating 5 MTD partitions on "Ractrends": 0x00000000-0x02000000 : "fullpart" 0x015a0000-0x01c40000 : "root" 0x01c60000-0x01da0000 : "www" 0x01dc0000-0x01ee0000 : "params" 0x00020000-0x01000000 : "coredump" NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 8192) ip_conntrack version 2.1 (496 buckets, 3968 max) - 292 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 6704 blocks [1 disk] into ram disk... done. Freeing initrd memory: 6704k freed VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 68k init modprobe: modprobe: Can't open dependencies file /lib/modules/2.4.22/modules.dep (No such file or directory) Creating ext2 ramdisk for /var of blocksize 4096 block count 256 ...mke2fs 1.37 (21-Mar-2005) ext2fs_check_if_mount: No such file or directory while determining whether /dev/ram1 is mounted. done. Creating directories in /var ...done. Creating ext2 ramdisk for /var/log of blocksize 4096 block count 256 ...mke2fs 1.37 (21-Mar-2005) ext2fs_check_if_mount: No such file or directory while determining whether /dev/ram2 is mounted. done. done. Activating swap. Calculating module dependencies... done. Loading modules: helper Warning: loading /lib/modules/2.4.22/misc/helper.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Helper Module Driver Version 1.0 Copyright (c) 2002-2003 American Megatrends Inc. [KERNINFO] [helpmain.c:172]used flash start is ff380000, used flash size is c80000 Module helper loaded, with warnings gpiomgr Warning: loading /lib/modules/2.4.22/misc/gpiomgr.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules GPIO Manager Driver Version 1.0 Copyright (c) 2002-2003 American Megatrends Inc. Module gpiomgr loaded, with warnings ppcgpio Warning: loading /lib/modules/2.4.22/misc/ppcgpio.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules PPC 405 GPIO Driver Version 1.0 Copyright (c) 2002-2003 American Megatrends Inc. Skipping....AFT_MODE_L Skipping....USB_FULLSPD Skipping....PPC_USB_RX_N Skipping....PPC_USB_RX_P Skipping....PPC_USB_OE_L Skipping....PPC_USB_TX_P Skipping....PPC_USB_TX_N Skipping....PPC_USB_RXD Skipping....PPC_PWR_ON_RESET [KERNINFO] [pgm_mg9064.c:169]Type 0 of Size 59215 Bytes ProgramFPGA906X successful Module ppcgpio loaded, with warnings videocap Warning: loading /lib/modules/2.4.22/misc/videocap.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Video Capture Driver Version 1.0 Copyright (c) 2002-2003 American Megatrends Inc. [KERNWARNING] [capmain.c:154]Unable to Find the DMA of FPGA MG906X. Running in Non DMA Mode [KERNWARNING] [capmain.c:158]FPGA Programmed at CS:0 Base:e0000000, IRQ:18, DMA:0 Module videocap loaded, with warnings usb-endpoint Warning: loading /lib/modules/2.4.22/misc/usb-endpoint.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Initializing USB Devices USB Device Endpoint Driver Copyright 2001-2003 American Megatrends Inc. GetMouseReportSize() MouseMode is 1 ReportSize = 32 ISP1181_Init: Called for ISP1181 Device 0 with DeviceNo 0 CHIPID = 0x8141 Clock done D E ISP1181_Init: Called for ISP1181 Device 1 with DeviceNo 1 CHIPID = 0x8141 D E usb_endpoint: Allocating new DPRAM for endpoint paramter block A B usb_endpoint: Allocating new DPRAM for endpoint paramter block A B usb_endpoint: Allocating new DPRAM for endpoint paramter block A B C MPC8248_Init: Device 0 Initialized with DeviceNo 2 D E F G H DevNo = 0 K IntrMask for Device(0): 0x307 DsviceNo = 0simrh a00 simrl 900000 H DevNo = 1 K IntrMask for Device(1): 0x307 DsviceNo = 1simrh b00 simrl 900000 H DevNo = 2 I MPC8248_Enable: Entering simrh b00 simrl 900020 usbmr = 2f7 Z MPC8248 ReConnect UsbBusSuspend(): Called for Device 0x1 UsbBusSuspend(): Called for Device 0x0 I USB Driver is Successfully Initialized Module usb-endpoint loaded, with warnings i2c-core i2c-core.o: i2c core module i2c-algo-82xx i2c-algo-82xx.o: i2c mpc82xx algorithm module loaded i2c-adap-82xx i2c-adap-82xx: Allocating new DPRAM for I2C paramter RAM i2c-algo-82xx.o: Adapter routines for CPM 82xx On-chip adapter registered i2c-core.o: adapter CPM 82xx On-chip adapter registered as adapter 0. i2c-algo-82xx.o: CPM 82xx I2C controller intialized with 8-bit slave address: 0x20 i2c-dev i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-dev.o: Registered 'CPM 82xx On-chip adapter' as minor 0 kcs Warning: /lib/modules/2.4.22/misc/kcs.o symbol for parameter Arg not found Loading Module ............this message should come Sample Module Driver Version 1.0 Copyright (c) 2002-2003 American Megatrends Inc. KCS Chip ID = 0xb0 Module kcs loaded, with warnings bob bob driver loaded Checking all file systems... fsck 1.37 (21-Mar-2005) Setting kernel variables ... kernel.core_pattern = /coredump/core kernel.core_uses_pid = 1 ... done. Mounting local filesystems... /dev/mtdblock2 on /usr/local/www type cramfs (rw) /dev/mtdblock3 on /conf type jffs2 (rw) /dev/mtdblock4 on /coredump type jffs2 (rw) Cleaning /tmp /var/run /var/lock. Setting the System Clock using the Hardware Clock as reference... System Clock set. Local time: Thu Jan 1 00:00:46 GMT 1970 Setting up networking...done. Hostname: SUNSP00144F0E240D. Setting up IP spoofing protection: rp_filter. Configuring network interfaces...done. Running ntpdate to synchronize clockError : Temporary failure in name resolution . Starting portmap daemon: portmap. Initializing random number generator...done. Running FRU update program: frutool... frutool::info::machine type: Sun Fire X4200, build P2 frutool::info::update: working on ASSY,MOTHERBOARD,G2 at 0x52 frutool::info::update: found IPMI FRU at 0x52, offset: 512 frutool::info::update: working on ASSY,SERV PROCESSOR,G1/2 at 0x53 frutool::info::update: found IPMI FRU at 0x53, offset: 512 frutool::info::update: working on ASSY,FRONT I/O BOARD,G2 at 0x50 frutool::info::update: found IPMI FRU at 0x50, offset: 512 frutool::info::update: working on ASSY,POWER BOARD,G1/2 at 0x51 frutool::info::update: found IPMI FRU at 0x51, offset: 512 frutool::info::all FRUs updated successfully frutool done INIT: Entering runlevelz Starting system log daemon: syslogd and klogd. Starting portmap daemon: portmap. Starting Network Interface Plugging Daemon: eth0. Starting IPMI Stack...... Done. Starting OpenBSD Secure Shell server: sshd. Starting log copying daemon: logcopier. Waiting for all KCS interfaces to go up...15 seconds left Waiting for all KCS interfaces to go up...12 seconds left Waiting for all KCS interfaces to go up...9 seconds left All KCS Interfaces seem to be up Releasing Opteron reset.....Done Starting CDServer :cdserver. Starting FDServer :fdserver. Starting HIDServer :hidserver. Starting Video Server :videod . Starting Flasher :flasher. Starting password reset daemon: password_reset. SUNSP00144F0E240D login: root Password: Sun(TM) Integrated Lights Out Manager Version 1.0 Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers. Portions may be derived from Berkeley BSD systems, licensed from U. of CA. Sun, Sun Microsystems, and the Sun Logo are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Federal Acquisitions: Commercial Software -- Government Users Subject to Standard License Terms and Conditions. Copyright 2005 Sun Microsystems, Inc. Tous droits rC)servC)s. DistribuC) par des licences qui en restreignent l'utilisation. Le logiciel dC)tenu par des tiers, et qui comprend la technologie relative aux polices de caractC(res, est protC)gC) par un copyright et licenciC) par des fournisseurs de Sun. Des parties de ce produit pourront C*tre dC)rivC)es des systC(mes Berkeley BSD licenciC)s par l'UniversitC) de Californie. Sun, Sun Microsystems, et le logo Sun sont des marques de fabrique ou des marques dC)posC)es de Sun Microsystems, Inc. aux Etats-Unis et dans d'autres pays. Warning: password is set to factory default. ->